1. Introduction

A glass furnace is a core thermal piece of equipment in a glass production line. Its operating condition directly affects the melting quality of the glass melt, production efficiency, energy consumption, and the service life of the glass furnace. Among the many operating parameters of a glass furnace, glass furnace pressure is an important control parameter that is easily overlooked. Glass furnace pressure is related not only to the combustion system, flue gas exhaust system, and glass furnace sealing condition, but also affects gas flow inside the glass furnace, the local thermal environment, and the stability of glass furnace operation. For end-fired glass furnaces equipped with a regenerative combustion system, glass furnace pressure control also faces the challenge of dynamic changes because combustion and flue gas exhaust are periodically reversed.

At the same time, refractories are exposed to severe conditions over long periods, including high temperatures, complex atmospheres, and corrosion by molten glass. Fused cast AZS blocks are widely used in critical areas of glass furnaces. Their service performance is related not only to the properties of the material itself, but also closely to the glass furnace structure, glass composition, and actual operating conditions. This article addresses the following questions: What is glass furnace pressure? How is glass furnace pressure controlled in an end-fired glass furnace? How are changes in glass furnace pressure related to the working environment of refractories? It introduces the basic concept of glass furnace pressure, its control principles, the reversing process, abnormal conditions, and its relationship with fused cast AZS refractories.


2. What is glass furnace pressure?

2.1 Basic concept of glass furnace pressure

Glass furnace pressure generally refers to the difference between the gas pressure at a measurement point inside a glass furnace and the atmospheric pressure outside the glass furnace. During glass furnace operation, fuel combustion generates a large volume of high-temperature flue gas. This gas flows through the glass furnace and is discharged through the regenerators, flues, and associated exhaust equipment. The pressure inside the glass furnace is jointly affected by the gases generated during combustion, resistance to gas flow inside the glass furnace, and the draft of the flue gas exhaust system. When the pressure inside the glass furnace is higher than atmospheric pressure, it is generally referred to as positive pressure; when it is lower than atmospheric pressure, it is referred to as negative pressure.


For a glass furnace, neither higher nor lower glass furnace pressure is necessarily better. In accordance with the design requirements, the pressure at a specified measurement point must be maintained within an appropriate range to ensure stable combustion, flue gas exhaust, and glass furnace operation. Glass furnace pressure is generally expressed in pascals (Pa) or millimetres of water column (mmH2O). The specific control target must be determined according to the glass furnace structure, measurement location, combustion method, and equipment design requirements. Therefore, the same setpoint cannot be directly applied to different furnaces.


2.2 Importance of glass furnace pressure control

Glass furnace pressure reflects the balance between gas flow inside the glass furnace and the flue gas exhaust system, and is one of the important parameters used to assess glass furnace operation. Proper glass furnace pressure control helps maintain a stable combustion environment, because changes in glass furnace pressure may affect gas-flow distribution, flame shape, and flue gas movement inside the glass furnace. Appropriate pressure control also helps reduce unnecessary gas leakage. When the positive pressure inside the glass furnace is too high, high-temperature flue gas may escape through gaps in the furnace structure, observation ports, and other openings, increasing heat loss and affecting the working environment. When the negative pressure inside the glass furnace is too great, outside cold air may enter through gaps or openings in the glass furnace structure, affecting local temperature and atmosphere.


In addition, abnormal glass furnace pressure may sometimes be related to changes in combustion load, changes in flue resistance, the reversing process, or equipment failures. Monitoring glass furnace pressure and its trends can help operators identify abnormalities in a timely manner. Changes in glass furnace pressure may also indirectly affect the working environment of refractories, but glass furnace pressure is not the only factor determining refractory service life. Even when glass furnace pressure is well controlled, refractory bricks may still be corroded by molten glass; conversely, fluctuations in glass furnace pressure do not directly prove that there is a quality problem with the refractories.


3. Structure and operating characteristics of end-fired glass furnaces

3.1 Basic operating principle of an end-fired furnace

An end-fired glass furnace is a representative type of glass furnace in which the flame follows a flow path with a characteristic horseshoe shape inside the glass furnace. In a typical regenerative end-fired furnace, fuel and preheated combustion air enter the glass furnace and burn. The resulting high-temperature flame and flue gas flow through the glass furnace, transferring heat to the glass batch and molten glass. During discharge, the flue gas usually passes through the regenerators. The checkerwork in the regenerators absorbs heat from the high-temperature flue gas and, in a subsequent stage, transfers the stored heat to the combustion air entering the glass furnace. To continuously recover waste heat from the flue gas, the system switches the combustion and exhaust functions on the two sides at predetermined time intervals. It should be noted that "end-fired" describes the flame-flow pattern, whereas "regenerative" describes the heat-recovery method. The actual furnace structure and control scheme should be determined by the specific design.


3.2 Main systems in glass furnace operation

Glass furnace pressure control is not an independent process; it is interconnected with the combustion, air supply, flue gas exhaust, and reversing systems. The combustion system is responsible for supplying fuel and combustion air and for the combustion process. The regenerators recover heat from high-temperature flue gas to preheat the combustion air. The reversing system periodically switches the combustion and exhaust functions on the two sides. The flue gas exhaust system conveys the flue gas generated by combustion to the flues and subsequent treatment facilities. The glass furnace pressure measurement system monitors the pressure at a specified location, while the glass furnace pressure regulation system adjusts dampers, induced-draft equipment, or other related actuators based on pressure feedback. These systems must operate in coordination. Even if the flue damper itself is operating normally, glass furnace pressure may still fluctuate if the reversing sequence, flue resistance, or combustion condition is abnormal.


4. Principles of glass furnace pressure control in end-fired glass furnaces

4.1 Basic objective of glass furnace pressure control

The basic objective of glass furnace pressure control is to maintain the pressure inside the glass furnace within the range specified by the design and to minimize unnecessary fluctuations. During actual operation, the control system needs to take into account the flue gas volume generated by combustion, resistance in the exhaust passages, chimney draft, and the operating condition of the induced-draft equipment. When the combustion load, flue gas temperature, or exhaust conditions change, glass furnace pressure may also change accordingly. Therefore, glass furnace pressure must be continuously adjusted according to actual operating conditions to maintain the overall stability of the glass furnace.


4.2 Adjusting glass furnace pressure with a flue damper

A flue damper is one of the commonly used devices for glass furnace pressure adjustment in some glass furnaces. By changing the effective flow area of the flue gas passage, the damper regulates the capacity for flue gas discharge. Under common control arrangements, with other conditions remaining essentially unchanged, appropriately increasing the damper opening will generally raise the flue gas discharge capacity and lower glass furnace pressure; appropriately reducing the damper opening may cause glass furnace pressure to rise. However, the relationship between damper opening and glass furnace pressure is not simply linear. In practice, the adjustment effect is affected by chimney draft, flue gas temperature, combustion rate, flue resistance, and the operating condition of other equipment. Therefore, operators need to make judgments based on pressure feedback and the overall operating condition of the furnace, rather than inferring glass furnace pressure solely from the damper opening.


In an automatic control system, the glass furnace pressure transmitter sends the measurement result to the controller. The controller compares the actual pressure with the setpoint and then sends an adjustment signal to the damper actuator, allowing the pressure to gradually return to the target range. This feedback control method can reduce the frequency of manual operation and improve the continuity of pressure control.


4.3 Adjusting glass furnace pressure through the induced-draft system

Some glass furnaces use an induced-draft fan or other flue gas extraction equipment to control flue gas exhaust. When the system uses an induced-draft fan to regulate exhaust capacity, the flue gas extraction capacity can generally be adjusted by changing the fan speed or related control parameters. Under common induced-draft control arrangements, increasing the induced-draft capacity will generally lower the pressure inside the glass furnace, while reducing the induced-draft capacity may cause glass furnace pressure to rise. However, flue gas exhaust system designs vary considerably among glass furnaces, and no single control method should be regarded as a universal solution for all end-fired glass furnaces.


4.4 Automatic glass furnace pressure control system

Modern glass furnaces generally use pressure-measuring instruments and automatic control systems to monitor glass furnace pressure. The basic control process can be summarized as follows: pressure measurement, signal feedback, comparison with the setpoint, controller calculation, and actuator adjustment, after which the pressure moves back towards a stable condition. Automatic control can reduce the frequency of manual adjustment and help improve the continuity of glass furnace pressure control. However, automatic control does not mean that the system can operate without human supervision. Pressure sensors, pressure-measuring lines, actuators, and control parameters may all affect control performance. When an abnormality occurs, the cause still needs to be investigated based on actual data.


5. Glass furnace pressure changes during reversing

5.1 Why does reversing affect glass furnace pressure?

In a regenerative end-fired furnace, reversing is an important operation that takes place periodically. Before reversing, one side mainly handles combustion and the supply of combustion air, while the other side mainly handles flue gas exhaust. After reversing, the operating functions of the two sides are exchanged. This process changes the flue gas flow path, the resistance on the exhaust side, and the local pressure distribution. At the same time, the supply of fuel and combustion air must also be switched according to the specified sequence. Therefore, even if the furnace can maintain relatively stable pressure during normal combustion, short-term pressure fluctuations may still occur during reversing.


5.2 Typical pressure changes during reversing

In some regenerative combustion systems, a short-term drop in pressure may occur during reversing, followed by a rise in pressure as the new combustion side comes into operation. This change is related to factors such as combustion input, flue gas flow rate, exhaust draft, and reversing sequence. However, not all furnaces exhibit the same pressure-change curve. Some systems have relatively small pressure fluctuations, while others may experience obvious short-term peaks or troughs. Therefore, when analyzing glass furnace pressure changes, the actual pressure trend chart and reversing signals should be considered together. Equipment condition should not be judged solely on the basis of one theoretical curve.


5.3 How can pressure fluctuations during reversing be reduced?

To reduce glass furnace pressure fluctuations during reversing, coordination among the reversing system, combustion system, and flue gas exhaust system must first be ensured. The fuel, combustion air, and flue gas exhaust systems need to be switched according to the established control sequence. An abnormal sequence may temporarily cause an imbalance between combustion and flue gas exhaust. At the same time, the dampers and actuators should be kept in proper working condition. If damper movement is delayed, the opening feedback is abnormal, or an actuator is faulty, pressure control may be affected even when the reversing program is correct.


Control system parameters also affect pressure changes. If the system responds excessively to short-term pressure fluctuations, it may cause frequent damper adjustments and even lead to new pressure fluctuations. Therefore, the control system needs to balance pressure response speed and stability. In addition, by monitoring pressure trends before and after reversing, operators can compare pressure changes over multiple reversing cycles, determine whether the fluctuations are repetitive, and further check combustion parameters, damper openings, and equipment conditions. Reversing control should follow the control logic and safety procedures provided by the furnace manufacturer. Interlock sequences or actuator operating parameters should not be changed arbitrarily based only on experience.


6. Common causes of abnormal glass furnace pressure and troubleshooting approaches

6.1 Persistently high glass furnace pressure

When glass furnace pressure remains above the target value, this may be related to insufficient flue gas exhaust capacity, increased flue resistance, abnormal damper operation, or changes in combustion load. In this situation, priority should be given to checking the flue damper operation, abnormal flue resistance, induced-draft equipment condition, and changes in fuel firing rate and combustion air volume. It is also necessary to confirm that the pressure transmitter and pressure-measuring lines are functioning normally. When the positive pressure inside the furnace is too high, high-temperature flue gas may escape through furnace openings or poorly sealed areas, increasing heat loss and affecting the working environment.


6.2 Persistently low glass furnace pressure

Low glass furnace pressure or excessive negative pressure may be related to excessively strong exhaust draft, an inappropriate damper opening, changes in combustion conditions, or abnormal pressure measurement. Based on the operating condition of the equipment, it is necessary to check the induced-draft system, flue dampers and actuators, fuel and combustion air supply, furnace openings and sealing condition, and confirm whether the measurement system is faulty. Excessive negative pressure may cause outside cold air to enter the furnace, affecting local temperature and the combustion atmosphere. Therefore, when glass furnace pressure is abnormal, the cause should be analyzed promptly and handled in accordance with operating procedures.


6.3 Frequent glass furnace pressure fluctuations

If obvious glass furnace pressure fluctuations continue to occur, the actual pressure, setpoint, damper opening, fuel flow, combustion air flow, and reversing signals can be plotted on the same time axis for analysis. For example, if pressure fluctuations always occur during reversing, the reversing sequence and exhaust conditions on both sides can be checked as a priority. If the pressure fluctuations have no clear relationship with reversing, the combustion load, flue gas exhaust system, and pressure measurement equipment need to be examined further. Analyzing the problem through trend records is more helpful for identifying the cause of an abnormality than simply observing the pressure reading at a single moment.


7. Relationship between glass furnace pressure control and fused cast AZS blocks

For a glass furnace, glass furnace pressure control is related not only to combustion and flue gas exhaust, but also to the operating environment in which the refractories are used. Fused cast AZS blocks are one of the important refractory materials used in glass furnaces. AZS is a commonly used abbreviation for refractories in the alumina (Al2O3), zirconia (ZrO2), and silica (SiO2) system. Fused cast AZS materials are produced through processes such as melting, casting, and subsequent heat treatment, and have material characteristics suitable for specific working environments in glass furnaces. These blocks are commonly used in critical areas such as tank sidewalls, the throat, and the passage, where material selection needs to be based on the type of glass, furnace design, and operating conditions.


7.1 Glass furnace pressure and the working environment of refractories

Glass furnace pressure is not the sole direct factor determining the service life of AZS blocks, but abnormal glass furnace pressure may indirectly change the working environment in certain areas. For example, when glass furnace pressure remains excessively high, high-temperature flue gas may escape through furnace openings or poorly sealed areas, which may be accompanied by local heat loss or changes in thermal conditions. When glass furnace pressure remains excessively low, outside cold air may enter the furnace, affecting local temperature distribution and atmosphere. If these changes persist and further affect the local thermal regime, they may indirectly influence the working conditions of certain refractory areas. However, the actual wear of AZS blocks also depends on factors such as molten glass composition, operating temperature, molten glass flow, vapour-phase corrosion, block structure, and material quality. Therefore, the degree of corrosion or service life of AZS blocks cannot be determined solely on the basis of abnormal glass furnace pressure.


7.2 Particular characteristics of the glass-line area

The glass-line area is an important refractory working area in a glass furnace. In this location, molten glass, the furnace atmosphere, and the refractory interact with one another. The material may be affected by various factors, including corrosion by molten glass, vapour-phase corrosion, and changes in local thermal conditions. If glass furnace pressure fluctuations cause changes in gas flow or local temperature, the working environment near the glass line may also be indirectly affected. However, wear in the glass-line area is often influenced by multiple factors. When analyzing its service life, it is necessary to consider glass composition, glass-level fluctuations, molten glass flow, temperature distribution, and the actual wear profile of the refractory. The issue should not be attributed simply to glass furnace pressure.


7.3 Material selection for tank sidewalls and other critical areas

The operating conditions in areas such as tank sidewalls, the throat, and the passage are not exactly the same. Tank sidewalls are in long-term contact with high-temperature molten glass, so attention needs to be paid to the material‘s resistance to corrosion by molten glass, structural stability, and service performance under specific operating conditions. Areas such as the throat and passage may be affected by molten glass flow and local thermal conditions. Material selection therefore needs to take temperature, glass composition, flow conditions, and furnace design into account. For the superstructure, the atmosphere, flame effects, and local temperature conditions are also important. The same material selection criteria cannot simply be applied to all areas. Therefore, in the design of refractories for a glass furnace, the AZS grade, block shape, and machining plan should be selected appropriately according to the working conditions in different areas.


7.4 Using operating records to assess furnace conditions

When evaluating the relationship between glass furnace pressure and refractory performance, it is important to consider operating records over a period of time rather than relying on an isolated measurement. A single pressure reading can show the condition at a particular moment, but it cannot fully explain how the furnace has been operating or whether a change is temporary or persistent. Recording actual pressure values together with the setpoint, damper position, fuel flow, combustion air flow, and reversing signals provides a more complete basis for analysis. These records can help operators identify whether pressure changes are associated with reversing, changes in combustion load, or variations in the flue gas exhaust system. The timing and duration of a pressure deviation are also worth considering. A brief fluctuation during reversing may be part of the dynamic response of a regenerative system, whereas a sustained deviation may indicate that the balance between combustion and flue gas exhaust has changed. However, the significance of either condition depends on the design and operating characteristics of the individual glass furnace. Operators should therefore compare the observed pressure trend with the furnace‘s normal operating pattern and the control requirements specified by the manufacturer. It is not appropriate to apply a universal pressure limit or adjustment method to every furnace.


A systematic approach is particularly useful when a refractory area shows signs of increased wear. For example, if damage or corrosion is observed near the glass line, the investigation should not begin by attributing the condition to glass furnace pressure alone. The actual wear profile should be examined together with the glass composition, glass-level fluctuations, molten glass flow, temperature distribution, and the local atmosphere. Pressure records may provide additional information about changes in the operating environment, but they need to be assessed alongside these other factors. The same principle applies to tank sidewalls, the throat, and the passage, where the operating conditions and forms of refractory attack may differ. 
Communication between the production team, furnace operation and maintenance personnel, furnace designer, and refractory supplier can make this assessment more effective. Operating personnel can provide pressure trends, reversing records, and details of changes in combustion or exhaust conditions. Maintenance personnel can report the location and appearance of refractory wear, while the refractory supplier can review the material grade, block shape, processing requirements, and relevant product test data. Considering these sources of information together helps distinguish between changes in operating conditions and issues that may be related to material selection or quality.


This approach does not mean that every pressure fluctuation will result in refractory damage, or that stable pressure alone guarantees a long refractory service life. Rather, it provides a practical way to understand the overall operating environment and avoid drawing conclusions from one parameter in isolation. By maintaining reliable operating records and evaluating them together with inspection findings, glass manufacturers can make more informed decisions about furnace adjustment, refractory selection, and maintenance planning.


8. How to select fused cast AZS blocks appropriately

8.1 Select materials according to the application area

The selection of AZS blocks should start with the specific application area. The conditions of contact with molten glass, temperature, atmosphere, and mechanical load may differ significantly from one area to another. Therefore, a material‘s suitability for all positions cannot be judged solely by its grade. Before selecting the material, as much information as possible should be clarified, including the furnace type and structure, the specific application area, the type of glass and molten glass composition, expected operating temperature, campaign duration and maintenance schedule, and block shape, dimensions, and machining requirements. This information helps suppliers and users conduct a more targeted material evaluation.


8.2 Focus on material properties and quality control

For fused cast AZS blocks, attention should be paid to the chemical composition, microstructure, porosity and defects, as well as relevant performance indicators. In actual evaluation, product technical data, test reports, and specific application requirements can be considered together. Different AZS grades may differ in composition and properties, and the performance of a particular product under all operating conditions cannot be inferred directly from the grade number alone.


8.3 Conduct a comprehensive evaluation based on actual operating conditions

The service performance of refractories is not determined by the material itself alone. Even if the material meets the quality requirements, abnormal wear may still occur if the actual operating temperature, glass composition, or operating conditions differ significantly from the design expectations. Therefore, appropriate material selection requires product properties to be considered together with furnace design, molten glass characteristics, and operating conditions. For glass manufacturers, effective communication between the refractory supplier and the teams responsible for furnace design, operation, and maintenance helps achieve a more accurate understanding of specific application requirements.


9. Stable furnace operation and appropriate refractory selection are equally important

A glass furnace is an interconnected thermal system. Glass furnace pressure control, combustion practice, reversing operations, flue gas exhaust conditions, and refractory selection are related to one another to varying degrees. The objective of glass furnace pressure control is to maintain stable furnace operation within the pressure range required by the design and to reduce unnecessary gas leakage and pressure fluctuations. The objective of refractory selection, on the other hand, is to choose materials with appropriate properties according to the actual working environment of each application area, and to make full use of their properties through proper installation, operation, and maintenance.


For fused cast AZS blocks, material quality needs to be evaluated in conjunction with actual operating conditions. When analyzing furnace operating problems, attention should be paid not only to operating parameters such as pressure, temperature, and combustion, but also to molten glass composition, refractory locations, and their actual wear conditions. Only by comprehensively analyzing these factors can the causes of problems be assessed more accurately and useful references be provided for subsequent material selection and furnace maintenance.


10. Conclusion

Glass furnace pressure is an important operating parameter in end-fired glass furnaces. Proper glass furnace pressure control helps maintain stable gas flow and a stable combustion environment, while reducing the risk of abnormal gas leakage and cold air infiltration. For furnaces equipped with regenerative combustion systems, pressure changes during reversing deserve particular attention. Through appropriate control logic, proper equipment operation, and continuous trend monitoring, the operating condition of the furnace can be better understood. At the same time, the service performance of fused cast AZS blocks in a glass furnace is affected by multiple factors. Glass furnace pressure and its changes may indirectly affect the working environment in certain areas, but actual material wear is also closely related to temperature, glass composition, molten glass flow, the gas-phase environment, and the properties of the material itself. Stable furnace operation and appropriate refractory selection complement each other. For glass manufacturers, a thorough understanding of furnace operating conditions and the selection of suitable fused cast AZS refractories according to the specific application area are important steps towards improving production stability and optimizing furnace operation management.